Double Glazing Door Lock Repairs

Are you experiencing issues with your uPVC window or door mechanism faulty? Perhaps the window or door handles aren't able to connect correctly or are difficult to use.

It is crucial that your double-glazed doors function smoothly, or else you'll be wasting energy and increase the chances of burglary. Owen the Locksmith will be able to fix your door lock at reasonable costs.

Snapped Key

If a key breaks in the lock, it can be incredibly annoying. It could also be a security risk because it could expose you to an intruder if the door is not locked. There are a few quick solutions you can use to repair the issue and make your door functional again.

Be calm. If you panic you may end up pushing the damaged key further into the lock.

Then spray WD-40 or another penetrating oil into the lock to help the broken piece slide out more easily. You can also use a screwdriver to help break pieces that might be hindering the flow. If you happen to have a little bit of the key that is sticking out, you can make use of a paperclip or other metal object with a thin surface to grab it and pull it out. Both of these methods work well, but be cautious not to push the broken piece of the key even further into the keyway.

Some paperclips come with grooved edges that can be used as hook extractors. Jigsaw blades can also work well for this. If you don't have any of these you can bend a hook with needle-nosed pliers. Additionally, you can use a pair tweezers to grasp and pull out the remaining pieces of broken keys.

If you are unable to get the broken piece of key out, try using a lock de-icer. It's available at most hardware stores and works by freezing any moisture present inside the lock.

If none of these solutions seem to work, it could be time to call a locksmith. Fitlocks specialists are able to quickly resolve issues with uPVC door locks and mechanisms, including snapped keys and broken handles. They can also reconfigure your double glazing repair glazing door mechanisms to allow them to operate more easily. Book a double glazing repair through us online or give us a phone call to discuss your requirements.

Broken Cylinder

A broken cylinder can pose a major security risk. A locksmith professional can fix the cylinder. Locksmiths will need to tap the cylinder to fix it. They can do this using an hammer or another tool, double glazing Repair but the most efficient method is to employ an extended match or piece of wire. Then, place the match's tip or wire close to the keyway. The locksmith will then hit the lock to crack it. This is superior to using a hammer, which can harm the lock.

The most frequent cause of cracks in the head of a cylinder is due to overheating. This can happen when the cylinder block and head are made of different metals, like cast iron and aluminium. Different metals can heat up and cool off at different rates. This can cause localised hotspots to expand faster than the rest.

Another possible cause of cracks in cylinders is corrosion. If the cylinder head as well as cylinder block are not properly maintained, this can result in corrosion or rust that could cause them to expand at a more than they ought to. Over time, this can also lead to cracks.

If your uPVC window lock or door is brittle or requires lots of pressure to turn, it can be the result of several things. This issue could result from a defective locking mechanism or misalignment as well as a worn-out handle.

Fortunately it is a simple and inexpensive fix for most double glazing owners. A professional locksmith will usually fix this problem within one hour of arriving at your home. They can fix the locking mechanisms, or replace the window handles and change the gearboxes, depending on your particular requirements. A skilled locksmith will always be able to provide you with a recommendation on the most cost-effective solutions for your home. They can also suggest upgrades to the highest-security 3 Star TS007 euro cylinders that will add an extra layer of security against burglars. It is a small cost to enjoy the peace of mind that comes from knowing your uPVC door is secured.

Broken Handle

It's not a surprise that window handle locks may break. They are equipped with complex mechanisms which deteriorate over time. If yours breaks it's difficult to pinpoint the cause of the issue. Make sure you fix it properly.

Repairing your damaged handle, whether it's the internal locking mechanism or latch, will improve the security of your uPVC door and reduce the risk of draughts. It can be expensive to repair or replace the handle in a way that isn't done correctly. It could also harm the frame and the lock of your door.

With the window open and the window open, loosen the screw that secures the handle with the screwdriver. This should be located on the inside of the back plate, and is normally covered by an aesthetically pleasing cover for the screw reasons. It is important to not lose any internal components of the handle like the levers and plates on either side. Ideally, keep these in the same order so you can replace them if needed.

Then, with a second screwdriver loosen the screw that connects the handle to the spindle at the back. Once the screw is loose, pull the handle out and remove the broken spindle. Replace it with a brand new one, making sure it's the same size as the old one (you can usually find these on the internet or at hardware stores) and screw it securely into the correct position. Do not overtighten the screw because this could harm the handle as well as the window frame.

Check that the new handle is fitted Close the window and test the handle. It should function smoothly and you'll be able to open your window once more.

While you're working on the handle, be sure to ensure that your uPVC windows are shut correctly. If they aren't closing correctly, you could encounter damp or draughts in your home. It could also affect the energy efficiency of your home. Core Sash Windows is a local window company that can adjust the hinges on the window frames to ensure that they close properly.

Broken Spindle

It is often the case that the spindle in a handle breaks rather than the handle itself. This is particularly common with uPVC tilt-and-turn windows. These windows require a handle to operate a locking device in the window frame. The handle is connected to a central rod that triggers the cams with a mushroom shape that lock into the window frame keep. If the dead latch mechanism fails to open when the handle is turned it is likely that the spindle has been damaged This can be an extremely frustrating issue.

Luckily there are ways to rectify this issue. A good locksmith will be able to quickly and effectively address this problem. They will be able to take apart the window handle using a tool that removes the wheel component of the mechanism, where the spindle is. This is done without damage to the handle or window frame.

Once the wheel is removed the technician can then inspect the spindle and determine what has caused it to break. This involves breaking the spindle into its constituent parts and carefully recording their general condition as well as any particular areas of wear or damage. This process is usually performed by technicians in an environment that is clean.

Then, clean the damaged spindle. This will remove any debris or dirt that could be hindering it from operating normally. The spindle could be replaced or repaired. If it's being replaced, the technician will need an identical dowel size to the original and drill mating holes in both pieces of the spindle. This will ensure that the spindle is perfectly matched with the handle.

If the spindle that is damaged is beyond repair, it could be necessary to replace it completely. Home centres sell generic substitutes but if the window style is rare you'll need to contact a cabinet maker or woodworker who can recreate the exact part. After the spindle is installed, it is attached to the handle. Line up the screw holes on the handle with the screws already in the frame. Once the new handle is installed, you are now ready to operate your uPVC window.