Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are long-lasting, durable and easy to maintain. They don't decay or rust as aluminum or timber.

It is essential to clean and oil UPVC windows and doors regularly. This will reduce unnecessary repair costs and increase energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause severe damage to your home and may even be fatal. It is important to make sure that your windows are in good shape.

For single pane windows, it is relatively easy to replace windows, and the new one will usually fit inside the frame that was previously installed easily. If you have double-paned windows which are joined by internal beading, it will be harder to remove and replace the old panes. In this case, you will need to locate some plastic spacers that assist the new pane to fit perfectly into the window frame.

Wearing eye protection and thick gloves is essential if you plan to remove the glass by yourself. You should also lay down a dropcloth before you begin working on the window panes, so that any shards fall onto the fabric, not onto the floor which could cause them to be trampled under.

Once the glass has been removed and the glass is removed, it's a good idea to cover the gap with some clear packaging tape or duct tape to prevent water and drafts from entering the property until a professional comes out and fix the window. This also serves as an obstacle to stop intruders from getting into your home. If the gap is large, you may be interested in the security door with an integrated window, since this will offer the best of both worlds.

2. Sagging

uPVC windows and doors are a cost-effective energy efficient, durable and long-lasting alternative to timber windows with sash. However, over time they are susceptible to a range of problems including sagging. A sagging uPVC window can cause issues with light, draughts, and even security. If you find that your Upvc window repair window is beginning to shrink, it is important to act swiftly to stop the issue from worsening.

Repositioning the hinges could help fix a window that is sagging. To accomplish this, you'll need open the window so that you can get to the frame. With an screwdriver, remove the hinges on the top and bottom and adjust them by turning them clockwise or anti-clockwise. After you've repositioned the hinges, shut your window and test it for an appropriate fit. If you're satisfied with the fit, tighten the screws until they stay in position.

If you aren't able to move the hinges, you might require replacing the seal. Seals made of rubber can dry out and lose their elasticity over time, leading them to loose their elasticity. If this happens, it's important to replace the seal as soon as you can to ensure that your uPVC windows are waterproof and safe from drafts.

uPVC handles could also loosen. This is often caused by screws that have been removed over time, but it can also be due to the mechanism of the handle wears out. Luckily, it's not difficult to repair the loose uPVC window handle yourself. You'll first need to close the window and then perform an initial fitting. The joint at the corner of the sash should align with the joint on the casing. If it does not you can use a screwdriver to loosen the handle. Then, you can turn the mechanism into position.

3. Water Leaks

It is crucial to take action if you get up each morning to find mouldy walls and floors that are wet. Water leaks through windows can cause structural damage to your home and hinder your ability to control the temperature inside your home. The most common reason for leaks in uPVC windows is that the sealant surrounding the frame is either damaged or is missing.

This is a fairly simple fix and should be undertaken by any competent DIYer. Depending on the severity of the issue is, old caulking might need to be removed. It is crucial to keep in mind that when it is about uPVC window repairs you should not be tempted to apply too much caulk' as this will only make the area more difficult to clean and can reduce your energy efficiency.

It is important to check that any drainage holes are clear of debris and that the sill pan is angled properly so that it drains away from the window. In more serious situations, you might have to consider replacing the window.

Other signs of long-term water leakage are rotted sills and the appearance of black spots of mold on the walls near the window. The fungus thrives in damp conditions and can spread quickly throughout the home.

It is also important to remember that if the leak originates from the glass in your repairing double glazed windows glazed windows, it's more likely to be a problem with the glass seal rather than the frame or sagging. It is also possible to be corrected by a uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or slack and blow open with ease It could be hinges that are at fault. Anyone with the skills to fix them can replace the hinges in a matter of minutes.

Almost every household in the UK will have either top hung or side hung uPVC windows that have hinges and like any mechanical part they are susceptible to wear and tear over time. Changing a window hinge is essentially a very simple procedure, but it is easier when you have a person to help you hold the frame in place.

It is also important to verify that the uPVC hinges are opening and closed in the right direction. You can do this by looking for the arrows on each hinge. This indicates the direction in which the window should open.

Window hinges that aren't working properly can be caused by incorrectly opening the window a certain manner or because of poor installation at the factory. This can often be resolved by sending us a photo through our website and we will be more than happy to give you suggestions.

It is also crucial to ensure that the hinges are lubricated on a regular basis. This can be accomplished by applying a light engineering oil to the hinges. We suggest using a solvent-free lubricant, such as 3-in-one Multi-Purpose Oil. Regular lubrication can allow the window open and close more easily. It can also stop corrosion and decrease the chance of sticking. Ideally, you should perform this every year. WD40 and other solvent-based fluids are not recommended since they will damage parts of your uPVC window.

5. Draughts

Draughts can be caused by a variety of different things. Firstly the hinges, again due to wear and tear can become misaligned, this will cause gaps to develop where the sash meets the frame. If they are damaged beyond repair, it may be required to realign them. Secondly the interlock, this is located on the hinge of the window, can be misaligned. Again, it is possible to just give them a thorough clean, however in certain cases, it may be necessary to have them replaced.

The second most frequent reason for draughts are the window seals, these are prone to wear or damaged over time and will allow air to escape through these gaps. This can be avoided by replacing them with high-quality weatherstripping. Another alternative is to replace the upvc window with low-emissivity glass. this will help in regulating indoor temperatures, UPVC Window Repair and also lessen the risk of draughts.

Another method of reducing draughts effectively is by using a Draught-excluder. These are usually fabric tubes filled with a filler, which can be put on top of your window sill. They will keep your home warm by blocking out cold air.