fiat 500 key fob reset 500 Replacement Key Fob

If your 500 remote key fob isn't working, it might be time to replace the battery. If you replace the battery but it still doesn't work, the problem may be elsewhere.

At United Locksmith, we specialize in the creation of new keys for old automobiles. We have the tools as well as the parts required for this type of service.

Dead Coin Battery

A dead battery is the primary reason for your Fiat 500 keyfob not locking or unlocking the doors. The key fob has the battery of a coin-cell that is prone to draining quickly when it isn't utilized frequently enough. If your remote has started to show signs like a loss in range or stopped functioning in the middle of the night, then your battery may be dead.

The battery in the key fob is held in place by steel clips that hold it in place. If the clips aren't tight, they can cause problems with the contact, which can stop the remote from receiving power. By using a small flathead screwdriver, break the clip that holds the retaining pin open to take out the battery and then insert a fresh one. Be sure to use an identical replacement battery kind of voltage, size and specifications as the original battery.

The key fob could also be damaged or corroded by exposure to water. Even a short bath in soapy, warm water could cause damage to the chip. Keep your key fob dry.

Water Damage

If your key fob isn't functioning properly, it may be caused by water damage. Key fobs come with rubber seals to protect them from being damaged by a light rain or splashes of water, however it is very important to keep your car keys from being tossed into the ocean, pool, and the washing machine!

The key fob contains an electronic chip that transmits a message to the immobilizer of your car. The chip is what allows the 500 to start and lock. If it gets wet it will not function.

If you want to check whether your key fob still working you can clean the internal electronics using isopropyl or electronic cleaner. However, it's better to purchase a new one from a dealership rather than trying to fix the key fob that was submerged in salt water.

A replacement fob can cost you a little bit but it's far cheaper than having to have your Fiat 500 towed to a dealer and repaired there! Additionally, you can do it yourself with a few easy steps. Be sure to have the correct battery type prior to opening your key fob. This is a job that's far simpler than it appears and you can find step-bystep instructions online for virtually any car key fob.

Faulty Chip

The chip inside the key fob communicates with the immobiliser of your car to ensure that the vehicle will only start once the correct keys are used. If the chip is damaged or corrupted in any way the car won't start.

A damaged chip could occur due to a variety of reasons but the most common reason is water damage or an unresponsive battery. It is best to hand Fiat 500 key fob Reset over the job to a professional locksmith who can replace the chip in a short time and at a an affordable cost.

If your key fob will not work after exposure to clean tap or rain water take it off the battery. Wipe down the electronic component using paper towels. If the key fob isn't working, it is likely a fried chip and will require replacement.

Some people will go to their dealer in order to get a new fiat 500 key fob reset fob. However, this can be costly. United Locksmith is the best option for you if want your Fiat key fob replaced at a reasonable cost. We have all the tools and knowledge required to fix your Fiat fob in a professional and timely way.

Faulty Receiver Module

Fiat key fobs send a signal to the vehicle that can unlock and close doors (and start the vehicle for those with an automatic transmission) up to 50 feet. However, there are a few things that can cause the fob to stop functioning. These include a dead coin battery or water damage buttons, worn ones, a receiver module issue and signal interference or a malfunctioning electronic chip.

If the fob was in a pocket which has suffered severe trauma (such as being dropped onto a hard floor or being washed in the washing machine) the fob may not be in a position to connect with the Body Control Module (BCM) of the car. The BCM is a security system that can only accept signals from genuine keys.

It is necessary to replace the fob if this happens. A professional locksmith can take care of every aspect of the replacement procedure as well as programming a new one for the 500. In fact, they could provide you with a clone key that functions exactly like your original fob (and costs less than the cost).