Fiat 500 Replacement Key Fob

If your remote key fob has stopped working, it may be time to replace the battery. However, if you replace the battery and it continues to stop working, then the problem could be elsewhere.

At United Locksmith, we specialize in the creation of new keys for classic automobiles. We have all of the tools and parts necessary to perform this service.

Dead Coin Battery

A dead battery is the most frequent cause of your Fiat 500 keyfob not locking or unlocking the doors. The key fob contains a coin cell battery that is prone to draining quickly when it isn't frequented enough. If your remote began to show signs of weakness like a loss of range and stopped working completely, the battery is probably dead.

The battery inside the key fob is held in place by steel retaining clips. If the clips aren't tight enough, they can cause problems with contact, which can prevent your remote from receiving power. Use a flathead screwdriver break open the retaining clip and remove the old battery. Choose a battery that is the same size, voltage and specifications as the original.

Water exposure can also cause the key fob to corrode or locksmith be damaged. Even a short bath in warm, soapy water can damage the chip. Keep your key fob dry.

Water Damage

Water damage may be the reason behind your key fob's not functioning properly. The rubber seals on key fobs keep them from being damaged by a tiny drizzle or splash of water. However, it is crucial to keep the car keys away from the ocean, washing machine, and pool.

The key fob is equipped with an electronic chip that transmits a message to the immobilizer system of your vehicle. This is what allows your 500 to start or lock, locksmith but if the chip gets wet, it can no longer function.

You can try cleaning the inside electronics of your keyfob with isopropyl Alcohol or an electronic cleaner to see whether they're still working. However, it's recommended to purchase a replacement from a dealership rather than trying to repair a key fob that was submerged in salt water.

Although a replacement fob may cost you a bit of money, it is a lot cheaper than paying for your fiat punto replacement key 500 to be towed to a dealership and fixed! You can also make it yourself with a few simple steps. Be sure to have the correct type of battery before attempting to open your key fob. You can find step-by-step instructions for any key fob in your car online.

Faulty Chip

The chip in the key fob communicates directly with the immobiliser of your car to ensure that your vehicle will start only when the correct keys are used. If the chip is damaged or corrupted in any way the car won't start.

Water damage or a dead battery are the two most common causes of defective chips. Regardless of the reason, it is best to delegate this work to a locksmith, as they will be able to replace the chip quickly and at an affordable price.

If your key fob will not function after exposure to clean tap or rain water then remove the battery. Wipe down the electronic component using an old towel. If the key fob does not work, there is a chance that it has an issue with the component and requires to be replaced.

Some people go to their dealer if they require an entirely new Fiat fob. However, this can be a costly option. If you are looking for a cost-effective way to have your Fiat key fob repaired make sure you contact United Locksmith. We have the equipment and know-how required to repair your Fiat key fob in a quick and professional way.

Faulty Receiver Module

Fiat key fobs send an alert up 50 feet away to the vehicle, which allows it to unlock and lock the doors (and start the vehicle for those with automatic transmissions). However there are some things that can cause the fob to cease functioning. It could be due to a dead battery damaged by water buttons, worn out buttons or a problem with the receiver module, and signal interference or an electronic chip that is malfunctioning.

If the fob was in the pocket that has been subject to extreme trauma (such as being dropped onto the floor, or washed in the washer) the fob might not be able to connect with the Body Control Module (BCM) of the car. This is because the BCM is a secure system that can only accept signals from a genuine key and not any other.

It is necessary to replace the fob in case this happens. A professional locksmith can handle every aspect of the replacement process as well as programming a new one for the 500. They can even provide you with an identical fob that functions exactly the same way as the original (and costs just less than what it would cost).