Repairs to uPVC Windows

uPVC windows are a fantastic choice for modern homes. They are easy to maintain and durable, as well as long-lasting. They do not decay or rust as aluminum and timber.

It is essential to clean and oil UPVC windows and doors regularly. This will reduce repair costs as well as improve energy efficiency.

1. Broken Glass

The broken glass in your windows could cause severe damage to your home and even be fatal. It is crucial to take the time to ensure that you are doing everything you can to keep your windows in good condition.

Single-pane windows are relatively simple to replace and typically fit into frames that were previously in use very easily. If you have double-paned windows that are joined by internal beading, it will be difficult to remove and replace the panes that were previously in use. In this case, it is necessary to purchase plastic spacers to aid in fitting the new pane into the window frame.

If you plan to try to remove the window panes yourself, it is essential to wear the appropriate safety equipment such as gloves that are thick and eye protection. You should also lay down a dropcloth before you begin working on the window panes so that any shards fall on the fabric, not onto the floor, where they could be trampled under.

Once the glass has been removed from the window, it's best to cover the gap with some clear packaging tape or duct tape to block water and drafts from getting into the property until a professional comes out and fix the window. This will also act as a barrier, preventing any intruders to gain access into your home. If the gap is large, UPVC Window Repairs you might want to consider using an alarm door that comes with an integrated window, since this will offer the best of both worlds.

2. Sagging

Upvc windows and doors are an affordable, durable and energy-efficient alternative to timber windows with sash. Over time, they can develop a variety of issues that include sagging. A sagging window can cause problems with light, draughts, and even security. It's important to take action when you realize that your uPVC windows are falling down.

Repositioning the hinges can aid in fixing a window repair near me which is sagging. To do this, you'll have to open the window so that you can get to the frame. Then, you can remove the hinges at the top and bottom with a screwdriver and adjust the hinges clockwise or counter-clockwise. Close your window to test the fit after you've repositioned your hinges. If you're happy with the fit, you can tighten the screws to ensure they remain in the right place.

If you aren't able to move the hinges, you might require replacing the seal. Rubber seals may dry out and lose their elasticity with time, leading them to loosen. If this happens, it's crucial to replace the seal as soon as you can to ensure that your uPVC windows remain watertight and secure from draughts.

uPVC handles may also loosen. The majority of the time, this is caused by screws that have come loose over time. However, it can also happen because the handle mechanism has been worn out. It's relatively easy to fix a loose uPVC handle. The first step is to close the window and then perform an initial test fit. The corners of the sash should align with the casing joint. If it doesn't you can use a screwdriver to loosen the handle. Then turn the mechanism into position.

3. Water Leaks

If you're waking up to wet floors and damp walls each time it rains it's crucial to take action. Windows that leak water do are not just a cause for degrading of the structure of your home but also undermine your efforts to regulate the temperature in your home. The most frequent reason for leaking uPVC windows is that the sealant around the frame is damaged or is missing.

This is an easy fix that can be completed by any DIYer who has the ability. Based on the severity of the problem the caulking used previously may require removal before a fresh layer is applied. It is important to remember that when it comes to uPVC window repairs, you should not be tempted to 'over-caulk' as this will only make the area more difficult to clean and reduce the efficiency of your energy.

Verify that the drainage holes have no debris inside them and ensure that the sill pan is properly angled to allow the water to drain from the window. In more serious cases you might have to consider replacing the window.

Mold spots and rotted sills are also signs of water leakage. This mold thrives in damp environments and is able to quickly spread throughout the home.

It is also important to remember that if the leak is coming from between the glass of your double-glazed windows, it's more likely to be an issue with the glass seal rather than the frame or sagging. This can be easily fixed by an uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or are loose and open with a breeze It could be the hinges that are at fault. Anyone who is a skilled DIYer can fix the hinges in a matter of minutes.

Like any mechanical component hinges are prone to be damaged over time. The process of replacing a hinge on a window is essentially a very simple process, but it's simpler with someone else to assist in holding the frame up.

Verify that the uPVC hinges are open and closed in the right direction. Check for the arrows on each hinge to determine the direction in which the window should be opened.

Window hinges that aren't working properly could be the result of incorrectly opening the window in a particular manner or because of improper installation in the factory. Sending us a picture through our website can often solve the issue. We are always happy to give assistance.

It is also crucial to ensure that the hinges are lubricated regularly. Applying a light engineering lubricant on the hinges is a good method to accomplish this. We suggest using a lubricant that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can allow the window operate and close more easily. It can also prevent corrosion and decrease the chance of sticking. This should be done at least every year. WD40 and other solvent-based lubricants should not be used as they can damage your uPVC windows.

5. Draughts

Draughts in Upvc windows can be caused by different things. The hinges may also become unbalanced due to wear, which can cause gaps between the frame and sash. If they are damaged beyond repair, it may be necessary to get them re-aligned. The interlock, which is on the hinge side of the window, can also become misaligned, again it's feasible to give them a good clean, but in some instances it could be necessary to have them replaced.

The next common cause of draughts is the window seals, these can become worn down or damaged over time and let air escape through these gaps. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity lenses. This will help to regulate indoor temperatures and lessen draughts.

The last way to reduce draughts effectively is by using a Draught-excluder. These are typically fabric tubes filled with a filler which can be hung over your window sill. They can keep your home warm by blocking out cold air.

The windows made of upvc can keep providing excellent insulation and security for your home with regular maintenance and repairs. However, uPVC window repairs it is important to recognise that all windows have a lifespan and eventually, they will reach the point when it's more economical to replace them than repair them. If you encounter any issues with your Upvc window, it's best to consult a professional immediately.