UPVC Window Handle Replacement

It is easy to repair a broken window handle with the proper tools. But it's essential to know your type of handle and the spindle's length prior to purchasing a replacement.

Older uPVC window handles have a spur which protrudes and locks over a cockspur wedge striker. They can be right-handed or left-handed and must be matched when replacing.

What type of lock or handle do you have? I have

There are a myriad of upvc window locks and handles each with its distinct advantages and functions. The type of handle that you have will determine whether or not your locking mechanism is efficient and if it is easy to open windows. Over time and through regular use, window handles made of upvc are prone to wear or damage. out, rendering them less secure and effective. In some instances, they could even fall completely off. It is important to repair your window handles made of upvc when you begin to notice they are falling off. This will prevent possible break-ins, and keep your house safe.

The good news is that replacing your upvc window handles is a relatively simple task that is achievable by almost everyone. You'll need a few basic tools, but with appropriate knowledge, it's an easy task that will only take a couple of minutes. You must know the type of lock or handle you have on your window. This will allow you to choose the appropriate replacement.

Inline Espagnolette Handles

They are typically located on the sides of the window. They have a flat design and come with a latch that connects to the locking mechanism on the frame of the window when it is turned. Inline upvc handles have a spindle that goes through the centre of the handle and into the frame of the window to activate the latch.

Cockspur Handles

They are typically found on older uPVC window frames. They have a distinctive, hook-shaped design. Cockspur handles have one screw that holds the handle to the frame of the window and are not as secure as other kinds of window handles.

Tilt and Turn Handles

The tilt and turn handles are different from other upvc handles because they can be turned for opening the window, and then tilted to the window to let air circulate. They feature a 7mm spindle at the back and are available in right and left-handed versions.

When you are purchasing replacement handles for upvc, it is important to measure the spindle's length since not all of them are the same size. To determine the length of your upvc handle, simply drop something in the middle of the hole, and then measure how far it extends before it reaches an obstruction. This is the longest spindle length that will fit in your window.

What is spindles?

uPVC window handles operate similar as doors, with the user turning the handle to activate a latch inside the frame. This opens the window so that it can be shut and opened. These handles can be damaged, especially if they're frequently used or exposed to harsh conditions. You may have to replace the handles on your uPVC window if they're not operating properly.

There are many different kinds of uPVC handles that are available, comprising Espag, Cockspur and Spaded handles. They are designed to fit in the uPVC frames in different ways, and each type of handle utilizes a specific spindle to lock the mechanism fitted to the window. This is why it is crucial to identify the type of handle you have on your uPVC window to get the correct replacement for it.

You can check what type of uPVC handle you have by looking at the base section of the handle. A snap-in cover should be over the screw that holds the handle's base in position. After removing this, you will be able observe the second screw that holds the handle base in place. After both screws are removed and you are able to pull the handle from the uPVC.

After you have removed the uPVC handle, carefully remove it from the locking mechanism. Make note of the length of the spindle, as you'll need to make sure that you buy an alternative that is the same length as your original handle and locking mechanism.

The spindle wears out and is unable to operate the locking mechanism. This can be caused by corrosion, damage due to continuous use, or even an unreliable locking mechanism. When this happens it will be necessary to replace the window handle and locking mechanism to restore full functionality to your uPVC windows.

How do I take off my old handle?

In the course of time and daily usage, window handles could become damaged or broken and if this happens, it is crucial to repair them as soon as possible to ensure the security of your home. It is simple to replace a damaged or worn handle. The task can be completed in under a minute without the need for any special tools.

The first step to remove the handle that was previously used is to remove the screw situated on the top of the base of the handle. Once the screw is removed, the handle will be removed from the base. Another screw will be located at the base of the handle. It can also be removed. Once these two screws have been removed, the handle will be removed from the window's base.

After removing the old handle and align the fixing holes of the new handle to the holes that are already in the window frame. If there is a cap or In my area sticker on the new handle remove it if necessary and then put the handle back in place. It is important to check that the handle is working after it is put in my area place. Turn the handle around and make sure the lock mechanism is activated.

Espag handles have a spindle which protrudes from the handle and slot into the multipoint locking mechanism on the window frame. Cadenza windows come with a blade with cutouts that are incorporated into the lock mechanism. Cockspur handles are long and hang over the outer frame of the window or the transom crossmember of the bar.

Once you have installed the new handle, place the spindle inside the window lock and tighten it. Replace the snap-in cover and screw cap (if necessary) once the handle is fixed. Once the handle is ready for use, simply open and close the window a couple of times to make sure that it functions properly and securely.

How do I install the new handle?

It's not that difficult to change the handle on your uPVC windows replacement. The process is very simple. All you require is a screwdriver and small amount of patience. First, make sure the old handle is unlocked. Remove any visible screws. You can also replace them using screw caps. After removing the handle, you need to make a note of the length of the spindle which protrudes from the back of the handle. This is crucial as it will determine what kind of handle to buy.

Espagnolette handles on uPVC are the most sought-after type of handle. The spindle passes through the handle to activate the locking mechanism inside the window frame. Once the handle is turned it releases the latch on the window, allowing it to open. In regular use and time, espagnolette handles may become damaged.

Cadenza handles are another type of uPVC window handle, which is typically used on tilt and turn windows. They have an elongated blade that functions as the multipoint locking mechanism inside the window. They are more secure than an espagnolette handles because they are able to open from the inside. They can be replaced by the same procedure as espagnolette handles but you must make sure that the new handle has a curved blade as opposed to one that is flat.

Once you've decided on the correct handle to purchase then you can place the new handle with the existing screw holes, and then screw it into the appropriate position. Then, put the screw covers back on and make sure the new handle functions properly. This is accomplished by shifting the handle from the locked position to the unlocked and the reverse direction a few times. It may be worth contacting an expert to determine if you can resolve any issues. They will often be able to guide you on the best solution to resolve the issue in a speedy and efficient way.