Reasons Your Fiat 500 Key Fob Won't Work

A key fob for fiat panda key replacement; click through the following internet site, 500 allows you to easily open doors and fiat panda key Replacement start your vehicle. There are a myriad of reasons the fob could stop functioning. This could be due to a dead coin-battery water damage, receiver modules issues, and interference.

This listing is for a NEW replacement key fiat 500 Fiat Flip Key Remote - an exact replica of the Ilco brand that must be professionally programmed by a local locksmith (click here to search for a Locksmith Search). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is the most common cause of your 500 key fob not working. Modern key fobs offer an operating range that is limited and must be within a few inches of your vehicle to work. If you are far from your vehicle, and you press the key fob button the car will not respond, and will display an "Key Fob Not Detected" message in the instrument cluster.

If this occurs you need to replace the battery of your coin-cell (Part Number CR2032) by a brand new one of a trusted brand like Panasonic Duracell or Energizer. They are usually available in your local hardware store, or online.

After you've replaced the battery of your coin cell you can test it by standing in front of your Fiat 500 and pressing the buttons. The car will flash its parking lights, and the key fob should operate the lock and unlock switches.

If your key fob still doesn't work even after replacing the battery, there might be water damage that prevents it from interacting with the module in your vehicle. Water damage can happen in a number of ways, ranging from the slightest splash to submerging the fob in salt water at the beach. If you think your fob was exposed to water, put it in a rice bag to draw out the moisture. If this doesn't work, you will require your fob to be reprogrammed either by an auto locksmith or dealer.

Water Damage

While the fob has some rubber seals that keep water out of the electronic chip inside and out of the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to become shorted and eventually end up dying. It's not good to soak the fob in water but don't give up when you accidentally drop it in the water or don't take it out of your pocket.

First, remove the battery. Before replacing the battery, clean the electronic chip with isopropyl or a similar product. Check the fob again to verify if it's working. If the key doesn't function then it might need to be reset. This is usually done by an auto locksmith or dealer.

If the key is newer and has never been programmed to your car It is likely that it needs to be replaced completely. A professional automotive locksmith will be able to complete this process. The locksmith needs to cut the key to match the ignition of your vehicle. The locksmith will also have to reprogram your fob in the car's system. This is a fast and affordable process which can be completed in the same day.

Receiver Module Issues

Your 500 key fob may not function because it's out of range. The remote typically has a range of 30 feet or less and if it's far from your vehicle, it won't respond to your commands. It's easy to fix this by moving the remote closer to your car until it responds.

If your fob won't work after replacing the battery for the coin, also known as a "button", "watch" or "button" It may be due to a malfunction on the circuit board inside. In most cases, reprogramming the fob will fix the problem. There are instructions on how to do this for all automobiles by searching YouTube or consulting the owner's manual.

You may need to replace the metal retaining clips that hold the battery of your coin in place. If they lose tension it can prevent your coin battery from being properly seated and cause your remote to malfunction.

In rare instances, the fob may become disconnected from your vehicle due to software issues or hardware issues. This can be a major issue, but you are able to usually fix it by visiting an auto locksmith to have them reprogram your fob. In some cases, they may need to reinstall the program in your body control module as well.

Interference

In addition to a dead coin battery, the key fob may not be able to transmit or receive a signal due to interference. This could happen if the key fob is located near a radio transmitter (cell phones, radar detectors) or another source of electromagnetic radiation. Other reasons the key fob may not function include a weak connection to the buttons or the internal chip or water damage.

If the key fob has been unable to function for a while without notice, or after trying everything you can do at home to resolve it e.g. replacing the battery, reprogramming, and using the spare key fob, you may have a faulty receiver module on your 500. The receiver module is located under the dash and is able to pick up the radio frequency signals from the key fob. It converts them to electronic commands that the vehicle interprets.

There's a simple method to reset the 500's on-board system including the keyfob. Disconnect the battery 12 volt for Fiat Panda Key Replacement approximately 15 minutes by removing the negative cable first then the positive cable. Then reconnect the battery. This will get rid of any residual electricity and restart the car's computers, which could allow you to the key fob to function again. If the issue persists you should speak with an experienced technician. They can identify the exact cause of any issues.