Double Glazing Door Lock Repairs

Are you experiencing issues with your uPVC window or door mechanism faulty? Perhaps the door or window handles don't meet up properly or are hard to use.

You will lose energy when your double-glazed doors do not perform as they should. This can also increase the likelihood of burglaries. Owen the Locksmith can repair your door lock at a reasonable cost.

Snapped Key

When a key snaps off inside a lock, it could be extremely difficult. It also poses a security risk, as the door might not lock and make you open to intrusion. There are fortunately quick fixes that you can attempt to fix the issue and get your door functioning properly again.

Keep calm. If you panic and start playing around with your keys you could end up pushing the damaged piece of the key deeper into the lock, making the situation worse.

Spray WD-40 or another penetrating lubricant into the lock. This will help the broken piece emerge more easily. You can also make use of a screwdriver to break up any pieces stuck that could be blocking the way. If you have a piece of the key that is still sticking out, grab it with a paperclip or another thin metal object and pull it. Both methods work well, however, be careful not to push the damaged piece of the key even further into the keyway.

Some paperclips have grooved edges, which can work in a pinch to extract hooks, and some Jigsaw blades also work for this purpose. If you don't have any of these items, you can bend a hook using needle-nosed pliers. Additionally, a pair of tweezers is a good way to grip and remove the remaining piece of the key that was broken.

If you cannot remove the broken piece of key Use a lock deicer. It's available in many hardware stores and works by freezing any moisture that may be present within the lock.

If none of these solutions seem to work, it could be time to consult a locksmith. Fitlocks experts can fix problems such as broken handles or broken keys with uPVC locks and door mechanisms. They can also reconfigure double glazing door mechanisms so that they are more easy to operate. Book a double glazing repair via our website, or give us a phone call to discuss your requirements.

Broken Cylinder

A damaged cylinder can pose an immediate security risk. Luckily, it's an easy repair for professional locksmiths to complete. Locksmiths will need to tap the cylinder in order to fix it. They can do this using the hammer or any other tool, but the most efficient method is to make use of a long match or a piece of wire. Then, put the match's end or wire near the keyway. The locksmith will then strike the lock in order to crack it. This is much better than using a heavy hammer, which could damage the lock.

The most frequent cause of cylinder head cracks is overheating. This can happen when the cylinder block as well as the cylinder head are made of various metals, like cast iron and aluminium. Different metals can heat up and cool off at different rates. This could cause localized hotspots to expand more quickly than the rest.

Corrosion is another possible reason for cylinder fractures. If the cylinder block and head are not maintained properly they may corrosion or rust and cause them to expand more than anticipated. As time passes, this may also cause cracks.

If your uPVC window or door lock is brittle or requires a lot of pressure to turn, this can be the result of many things. This issue could result from a defective locking mechanism or misalignment and also a worn out handle.

This is a straightforward and inexpensive fix that most homeowners with double glazing can perform. A professional locksmith can usually solve the issue within one hour of arriving at your home. They can replace the locking mechanisms, or change the window handles, and double glazing repair also change the gearboxes based on your particular requirements. A locksmith with experience can always advise you on the most cost-effective options for your home. They can recommend upgrading to 3 Star TS007 Euro Cylinders which give you an extra layer of protection from burglars. It's a small amount to enjoy the peace of mind that comes from knowing that your uPVC door is secured.

Broken Handle

It's not surprising that window handle locks may break. They have complex mechanisms that wear out over time. It isn't easy to determine the reason for the broken window handle lock and then fix it properly.

If the issue is with the internal locking mechanism or the latch, fixing your broken handle can improve your upvc repairs near me double glazing door's security and allow you stop draughts. Incorrectly repairing or replacing your handle can be expensive and could harm the door's frame as well as lock and frame, so it's worth spending some time to do it right.

With the window in the open position and the window open, loosen the screw holding the handle using a screwdriver. The screw should be located on the inside of the backplate, which is usually concealed by an eye-catching cap to conceal it to enhance the appearance. Be sure to not lose any of the internal parts within the handle, such as the plates or levers that are on the opposite side of the spindle. It is best to keep them in the same place so you can replace them again if needed.

Then, using a second screwdriver, loosen the screw that holds the handle to the spindle at the back. Once the screw is released, you'll be capable of pulling the handle off and take off the damaged spindle. Replace it with a brand new spindle, ensuring that it's the same length (you can find them online or at hardware stores). Securely screw it in the frame. Do not tighten the screw too much because this could harm the handle as well as the window frame.

Close the handle and try it. It is likely that it will operate smoothly and you'll be able to open your window once more.

Make sure to check that your uPVC window is shut properly when you're using the handle. If they're not closing properly, you could experience damp or draughts inside your home. You could also compromise the energy efficiency of your home. A local window company, such as Core Sash Windows, will be capable of adjusting the hinges on your window frames so they are able to shut properly.

Broken Spindle

It is often the case that the spindle within the handle breaks, rather than the handle itself. This is most common in uPVC tilt-and-turn windows. These kinds of windows require a handle which operates a locking mechanism in the frame of the window. The handle is attached to a central rod that triggers the locks that are shaped like mushrooms and secure into the frame of the window keep. If the dead latch mechanism fails to open when the handle has been turned, it is likely the spindle is damaged. This can be a problem that is frustrating.

Luckily there are options to rectify this issue. A skilled locksmith can quickly and efficiently fix this problem. A good locksmith will be able to disassemble the handle of the window by using a tool to remove the wheel part that houses the spindle. This can be done with no damage to the handle or the window frame.

Once the wheel has been removed, the technician will examine the spindle to determine what has caused it to break. This involves breaking down the spindle into its component components and carefully observing their general condition, double glazing repair as well as any specific areas of wear or damage. The process is performed in a clean room by highly skilled technicians.

Then, clean the damaged spindle. This will help get rid of any dirt or debris which might be preventing it from working normally. Following this the spindle can be repaired or replaced. If the technician is replacing the spindle the dowel can be used that is similar in size to the original. The technician will then drill holes that are identical to both pieces. This ensures that the new spindle is precisely matched to the handle.

If the damaged spindle cannot be repaired, it could need to be replaced entirely. Home centers sell generic replacements, but if the design of your window is rare then you will need to contact a wood worker or cabinet maker who can duplicate the exact part for you. Once the new spindle has been installed it can be attached to the handle by line up the screw holes in the handle with the frames existing screws. Once the new handle is firmly in place, you'll be able to operate your upvc window repairs window.