Repairs to uPVC Windows

uPVC is a great choice for modern homes. They are durable, long-lasting and easy to maintain. Unlike timber and aluminium, they are not susceptible to corrosion or rot.

It is crucial to wash and oil UPVC windows and doors on a regular basis. This will prevent unnecessary repair costs and increase energy efficiency.

1. Broken Glass

If the glass in your window is damaged, it could cause a large amount of damage to your home, making it very dangerous and potentially fatal. You should take the time to make sure that your windows are in good working order.

For single pane windows it can be relatively simple to replace them, and the new window will generally fit within the frame that was previously installed easily. However, if you have double-pane windows that are held in place by internal beading, it will be more difficult to take out the panes that are in place and replace them with new ones. In this case, it is necessary to buy plastic spacers to help the new pane fit into the window frame.

Wearing eye protection and thick gloves is essential if you plan to remove the glass yourself. It is also recommended to lay down a dropcloth before you begin working on the glass, so that any fragments of glass fall onto the cloth instead of onto the floor where they can be trampled on and cause further damage.

It's a great idea tape the gap once the glass is removed. This will prevent water and drafts from entering your property until a professional is able to repair the window. It also acts as a barrier, preventing any intruders to gain access into your home. If the gap is particularly large, you may want to consider using an alarm door that comes with an integrated window, since it offers the best of both worlds.

2. Sagging

Upvc is a long-lasting energy-efficient, cost-effective and economical alternative to timber sash windows. As time passes, they may develop a number of problems that include sliding. A sagging window can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to sag it is important to act swiftly to prevent the problem from becoming worse.

To repair a window that is sagging, you can try to reposition the hinges. To accomplish this, you'll have to open the window to access the frame. With the screwdriver, you'll be able to unscrew the hinges on the top and bottom and adjust them by turning them clockwise or counter-clockwise. Once you've adjusted the hinges, shut your window and check for fit. If you're satisfied with the size of the window, you can tighten screws to keep them in place.

If you are unable to reposition the hinges you may need to replace the seal. As time passes, rubber seals lose their elasticity and become dry which causes them to lose tightness. If this happens, it's important to replace the seal as quickly as possible so that your uPVC windows are waterproof and safe from drafts.

UPVC handles can also loosen up. The majority of the time this is due to screws that have come loose over time. However, it can be due to the fact that the handle mechanism has worn out. Fortunately, it's easy to repair the loose uPVC window handle yourself. First, you'll need to shut the window and then perform a test fitting. The corner joints of the sash need to be aligned with the casing joint. If it doesn't then you can make use of a screwdriver to loosen the handle and return the mechanism to its original the position it was in.

3. Water Leaks

It is crucial to take action if you get up each morning to find a smoky wall and floors that are wet. Water leaks through windows can cause structural damage to your home and also hinder your ability to control the temperature in your home. Most often, uPVC window leaks are caused by a damaged or missing sealant.

It is a fairly easy fix that can be completed by any DIY expert. Depending on how serious the issue is, old caulking may need to be removed. When it comes to uPVC repair, you must be careful not to over-caulk. This can make your window harder to clean and lower its energy efficiency.

It is essential to ensure that the drainage holes are clear of debris and that the sill pan has been angled properly so that it drains away from the window. In more severe situations, you may have to replace the window.

Other indicators of water leakage are sills that are rotten and the appearance of black spots of mold on the wall near the window repair. This fungus thrives under conditions of dampness and can spread quickly throughout the home.

It is also important to keep in mind that if the leak originates from the glass of your double glazed windows, it's more likely to be an issue with the glass seal, rather than the frame or sliding. Again this can easily be repaired by an uPVC window expert who can replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

Hinges may be to blame for the reason that your uPVC window is difficult to open or it opens in the breeze. Any competent DIYer can replace hinges in just a few minutes.

Like any mechanical component hinges will wear out over time. It is very easy to replace a hinge on a window however it is simpler if you have someone to help you to hold the frame.

It is also important to ensure that the uPVC hinges are opened and closed in the right direction. This can be done by looking for the arrow on each hinge. This indicates the direction in which the window should be opened.

The issue can be caused by opening the window improperly or by a poor installation at the factory. This issue can be fixed by sending us a picture on our website. We will be pleased to offer you advice.

It is also essential to grease the hinges on a regular basis. Applying a light engineering lubricant on the hinges is an ideal method of doing this. We suggest using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It also helps prevent corrosion and decrease the chance of sticking. The ideal time to perform this every year. WD40 and other solvent-based oils are not recommended because they can damage the parts of your uPVC window.

5. Draughts

Draughts can be caused by different causes. Firstly the hinges, again because of wear and tear, may become displaced, which will cause a gap to form where the sash joins the frame. If they are damaged beyond repair, it could be necessary to have them realigned. The interlock may also become unbalanced. This is located on the hinge's side and uPVC could require to be cleaned. In some cases, it may be necessary to replace these.

The next common cause of draughts is the window seals. They are prone to wear or damaged over time, and will allow air to escape through these gaps. This can be prevented by replacing them with high-quality weatherstripping. Another option is to replace the upvc window with low-emissivity glass. which will help regulate indoor temperatures, and also reduce the risk of draughts.

The final method to cut down on drafts effectively is to use a Draught-excluder. These are typically fabric tubes filled with a filler that can be put on top of your window sill. They will keep your home warm by blocking out cold air.

With a little regular maintenance and repair windows made of upvc will provide a great level of security and insulation for your home. It is crucial to keep in mind that all windows will eventually get worn out and uPVC it may be more cost-effective to simply replace them instead of fixing them. If you have any problems with your upvc window, it's best to consult an expert as soon as possible.