UPVC Window Handle Replacement

It is easy to repair a broken window handle using the appropriate tools. However, it is essential to know the type of handle and the spindle's length prior to purchasing the replacement.

Older uPVC window handles have a spur that extends and is locked over the wedge striker for cockspur. They can be right or left-handed and have to match when replacing.

What type of lock and handle do I need?

There are many window locks and handles made from upvc each with its own advantages and purposes. The type of handle that you choose will determine whether or not your locking mechanism is effective and if it is easy to open the windows. With time and regular use, the upvc handles on your windows may get worn out and damaged. This makes them less secure and effective. In some cases they may even fall completely off. It is crucial to fix the handles on your window made of upvc when you begin to notice them falling off. This will avoid burglaries and keep your home safe.

It's an easy task that virtually anyone can perform. With just a few tools and the proper knowledge, this is a simple procedure that should take no more than a couple minutes. You will need to know the type of lock or handle you have on your window. This will allow you to choose the appropriate replacement.

Inline Espagnolette Handles

They are usually found on the side of the window. They are flat and have an open latch that is connected to the locking mechanism of the window frame. Inline upvc handles also have a spindle that goes through the centre of the handle and into the frame of the window to operate the latch.

Cockspur Handles

These handles are typically located on older uPVC windows and have an distinctive hook-shaped design. Cockspur handles are fitted with a single screw that holds the handle to the window frame and are not as secure as other types of window handles.

Handles that tilt and turn

In contrast to other handles made of upvc, tilt and turn handles can be rotated to open the windows and turned inwards to allow for Window Handle Replacement ventilation. They typically have a 7mm spindle at the side of the handle. They are available in both left and right-handed versions.

It is crucial to determine the spindle's size prior to purchasing a replacement handles made of upvc. Not all of them are exactly the same size. To test the length of your upvc handle simply drop something into the middle of the hole and measure how far down it goes before it comes into contact with an obstruction. This is the length of the spindle that will fit your window.

What is a spindle?

uPVC window handles operate similarly to doors. By turning the handle, you can operate a latch within the frame. The window is then opened and shut. However, sometimes these handles can become damaged, especially when they are frequently used or exposed to harsh weather conditions. It is possible to replace the handles on your uPVC window if they're not functioning correctly.

There are many different kinds of uPVC handles available comprising Espag, Cockspur and Spaded handles. These handles are designed in a variety ways to fit into uPVC frames. Each handle type uses an entirely different spindle for locking the window mechanism. It is crucial to know the kind of handle that is installed on your uPVC windows to ensure that you replace it with the right one.

You can find out what kind of uPVC handle you have by taking a look at the base of your handle. A snap-in covers should be over the screw that holds the base of the handle in place. When you remove this cover you will be able to see the screw that holds the handle base in position. After both screws are removed and you are able to remove the handle from the uPVC.

After taking off the uPVC handle, carefully remove it from the locking mechanism. Be sure to note the length of the spindle since you'll need to make sure that you buy one that is the same length as your original handle and locking mechanism.

The spindle wears down and cannot operate the locking mechanism. This can be caused by corrosion, damage caused by constant use or the locking mechanism becoming looser. If this happens, you will have to replace both the window handle and locking mechanism to restore the full functionality of your uPVC Windows.

How do I remove the handle that was previously attached?

Over time and through everyday use, window handles may become damaged or broken, and if this happens, it is crucial to repair them as quickly as possible to ensure the security of your home. It is easy to replace a worn or damaged handle. The task can be accomplished in less than one minute without the need of special tools.

To take off the handle, you first need to remove the screw at the bottom of the handle. Once the screw is removed, the handle can be removed from the base. There is another screw located at the bottom of the handle base, and it is able to be removed too. After both screws are removed, the handle can be completely detached from the base of the window.

After the handle has been removed, take the new handle and align the fixing holes with the holes currently in the window frame. If there is a sticker or cap on the new handle, remove it if required and screw the handle into place. Once the handle is in place, it is essential to check that it works by turning the handle, and ensuring that the lock mechanism activates.

Espag handles have an elongated spindle that extends from the handle and slot into a multipoint locking mechanism inside the window handle replacement frame. Cadenza windows come with blades with cut-outs that slot into the lock mechanism, while Cockspur handles have a long nose that is able to hook over the frame's outer or transom bar cross-member within the window.

Once you have installed the new handle, insert the spindle inside the window lock and tighten it. Replace the snap-in cover and screw cap (if necessary) after the handle is fixed. The handle is now ready to use, so try opening and closing the window a few times to make sure that it functions correctly and securely.

How do I install the new handle?

It's not that difficult to change the handle on your windows made of uPVC. The process is simple. All you require is a screwdriver and a small amount of patience. First, ensure that the handle is not locked. Then remove any screws visible. You could also replace them with screw caps. After the handle has been removed, you need to make an note of the length of the spindle that extends from the back of the handle. This is important as it will determine the type of handle you'll need to purchase.

Espagnolette handles on uPVC are the most sought-after type of handle. The spindle runs through the handle to operate the locking mechanism within the frame of the window. The handle releases the latch and allows the window to open. With time and Window Handle Replacement regular use, espagnolette handles could be damaged or damaged, making it necessary to locate a replacement.

Cadenza handles are another type of uPVC window handle that is commonly used on tilt and turn windows. They feature a protruding blade that operates an interlocking mechanism that is multipoint within the window. They are more secure than an espagnolette handle as they can only open from the inside. You can replace them using the same procedure as you would for espagnolette handles however, make sure that the new handle is angled, not flat.

After you have chosen the right handle, simply align the new handle to existing screw holes before screwing it into place. Then, put the screws on and test the new handle. You can perform this by dragging the handle between the locked position to the unlocked for a few times. If you have any issues, it could be worth contacting a specialist to see if they are able to help resolve the problem. They can offer advice on how to fix the issue in a quick and effective manner.