UPVC Window Handle Replacement

Replacing a damaged window handle is a relatively simple process and with the right tools it can be accomplished quite quickly. It's important to identify the kind of handle you have and its spindle size before purchasing an alternative.

Older uPVC window handles have a spur that extends and is locked over the cockspur wedge striker. These can be either left or right-handed and need to match when replacing.

What kind of lock or handle do I have?

There are a myriad of windows locks and handles made of upvc each with its distinct advantages and functions. The type of handle that you have will determine if your locking mechanism is efficient and if it's easy to open windows. With time and regular use the upvc handles that are on your windows may be damaged and worn out. This makes them less secure and Window Handle Replacement effective. In some instances, they could even fall off completely. If you notice that your upvc window handles have fallen off, it's essential to fix them as soon as you can. This will prevent possible break-ins, and keep your house safe.

The good news is that replacing your window handles made of upvc is a relatively simple task that is achievable by almost anyone. You will need a few basic tools, but with the right knowledge, it is a straightforward process that should take only a couple of minutes. To get started you'll need to determine the type of lock and handle you have on your window made of upvc and Window Handle Replacement then identify the best replacement.

Inline Espagnolette Handles

They are usually found on the outside of the window. They are flat and come with an open latch that is connected to the locking mechanism of the window frame. Inline upvc handles also have a spindle that runs through the center of the handle and then into the frame of the window to activate the latch.

Cockspur Handles

These handles are typically found on older uPVC windows and have an distinctive hook-shaped design. Cockspur handles have one screw that is used to secure the handle to the frame and are not as secure as other kinds of window handles.

Tilt and Turn Handles

Unlike the other handles made of upvc the tilt and turn handles can be turned to open the window, and the handle can be tilted to the side to allow ventilation. In general, they have a 7mm spindle on the side of the handle. They are available in left and right handed versions.

When buying replacement upvc handles It is crucial to verify the length of the spindle because not all handles are identical in size. To test the length of your upvc handle, simply drop something into the middle of the hole and then measure how far it extends before it reaches an obstruction. This is the maximum size of spindle that will fit in your windows replacement.

What is the spindle?

uPVC window handles function in a similar way to doors, by turning the handle to open an opening inside the frame. The window can then be opened and shut. The handles can become damaged, especially if they're frequently used or exposed to harsh environments. It is possible to replace the handles on your uPVC window if they are not functioning correctly.

There are many types of uPVC handles, including Espag, Cockspur, and Spaded handles. They are designed to fit into the uPVC frames in a variety of ways and each handle type uses a specific spindle to lock the mechanism to the window. It is essential to determine the kind of handle that is installed on your uPVC windows so that you can replace it with the right one.

The base of the handle will inform you what kind of uPVC it is. There should be a "snap-in' cover over one screw which holds the handle base in place. Remove this and then you should be able see the second holding screw on the opposite side of the base of the handle. Once both screws are removed you should be capable of pulling the handle away from the uPVC window.

After you have removed the uPVC handle, remove it from the locking mechanism. Make note of the length of the spindle since you'll need to make sure that you purchase a replacement that has the same length as the original handle and locking mechanism.

The spindle wears down and is unable to operate the locking mechanism. This can be caused by corrosion, damage due to frequent use, or an unreliable locking mechanism. If this occurs, it will be necessary to replace the window handle and locking mechanism to restore full functionality to your uPVC windows.

How do I get rid of my old handle?

Window handles can become damaged or broken over time. It is crucial to fix them as quickly as you can to ensure your security. The good news is that replacing a damaged or worn handle is a relatively simple job that can be carried out in less than one minute and doesn't require any specialist tools.

To remove the handle, first remove the screw located at the base of the handle. Once the screw is removed, the handle can be pulled away. A second screw will be located at the base of the handle. It can also be removed. After these two screws have been removed, the handle can be removed from the window's base.

After the handle has been removed, take the new handle and line up the fixing holes with the holes that are present in the window frame. There may be a tiny sticker or caps on the new handle, so remove them if needed and then screw the handle into place. It is important to check that the handle is working after it is installed. Turn the handle around and make sure that the lock mechanism is working.

Espag handles have a spindle that protrudes from the handle and slot into a multipoint locking mechanism inside the window frame. Cadenza windows have a blade with cutouts that are incorporated into the lock mechanism. Cockspur handles are long and hook over the frame that surrounds the window or the transom crossmember of the bar.

After you have put in the new handle, slide the spindle inside the window lock and tighten it. When the handle is fixed in place, replace the'snap in' cover and the screw cap (if necessary). When the handle is in use, you can open and close the window a few times to make sure that it functions properly and securely.

How do I install the new handle?

It's not difficult to change the handle on your Upvc windows. The process is very easy. You'll need a screwdriver, and a bit of patience. The first thing you need to do is ensure that the handle is not locked and then remove any screws that are visible, you can also replace these by screw caps if you need. After you have removed the handle, you will need to note the length of the spindle that extends from the back. This is important because it will determine the kind of handle to purchase.

Espagnolette handles made of uPVC are the most sought-after type of handle. The spindle is inserted into the handle to activate the locking mechanism within the window frame. The handle opens the latch and allows the window to open. As time passes and with regular use, espagnolette handles may be damaged or damaged, making it necessary to locate an alternative.

Cadenza handles are a different kind of uPVC window handle commonly used on tilt and turn windows. They have a protruding knife that is operated by a multi-point locking mechanism inside the window. They are usually more secure than espagnolette handles since they are only accessible from the inside. They can be replaced with the same method as espagnolette handles, however you will need to ensure that the new handle has a curved blade, as opposed to flat ones.

Once you have selected the right handle, simply align the new handle with existing screw holes before screwing it into place. After that, you can put the screw covers on and test the new handle. This is done by moving the handle from locked position to the unlocked and vice versa several times. If you have any issues, it may be worth contacting a specialist to see if they are able to assist you in solving the issue. They can offer advice on how to fix the issue in a timely and efficient manner.