Repairs to uPVC Windows

uPVC windows are a great choice for modern homes. They are durable, long-lasting and easy to maintain. They do not decay or rust as timber and aluminum.

It is essential to clean and oil upvc repair - Click On this site - doors and windows on a regular basis. This will reduce repair costs and improve energy efficiency.

1. Broken Glass

If the glass in your window has been damaged, it can cause a great deal of damage to your home, which can make it very hazardous and possibly fatal. You should take the time to ensure that your windows are in good working order.

For single pane windows it is fairly easy to replace windows, and the new one will generally fit within the frame that was previously installed easily. If windows with double panes are joined by internal beading, it will be harder to remove and replace the panes that were previously in use. In this case you'll need find some plastic spacers to assist the new pane to fit perfectly into the frame of the window.

Wearing eye protection and heavy gloves is essential if you plan to remove the glass by yourself. It is also recommended to lay down a drop cloth prior to when you begin working on the glass so that any shards fall onto the cloth instead of landing on the floor, where they could be trampled upon and cause further damage.

Once the glass has been removed from the window, it's best to cover the gap with clear packaging tape or duct tape to stop drafts and water from entering the property until a professional comes out and fix the window. It also acts as a barrier, uPVC repair deterring any intruders from gaining entry to your home. If the gap is large, you may be interested in a security door uPVC repair that has an integrated window as this will offer the best of both worlds.

2. Sagging

Upvc is a long-lasting, energy-efficient and affordable alternative to timber sash windows. In time, they could develop a variety of issues such as sliding. A sagging uPVC windows can cause issues with light, draughts, and even security. If you find that your uPVC window is beginning to sag it's important to act quickly to prevent the problem from becoming worse.

To repair a window that is sagging, you can try to reposition the hinges. You'll first need to open the windows to get at the frame. Then, using an screwdriver, take off the hinges on the top and bottom and adjust them by turning them clockwise or anti-clockwise. Close your window to check the fit after you have relocated your hinges. If you're satisfied with the fit, tighten the screws to ensure that they stay in place.

If you cannot reposition the hinges, you might need to replace the seal. Rubber seals can dry out and lose their elasticity with time, leading them to lose their tightness. It is crucial to replace your seal as quickly as you can to keep your uPVC window watertight and draughtproof.

uPVC handles may also become loose. The majority of the time, this is caused by screws that have come loose over time. However, it can also happen because the handle mechanism has been worn out. It's relatively easy to fix a loose uPVC handle. You'll first need to close the window doctor and perform a test fitting. The joint at the corners of the sash should be aligned with the joint on the casing. If it isn't, you can use a screwdriver or a wrench to loosen the handle, and then reverse the mechanism back into position.

3. Water Leaks

If you wake up to wet floors and damp walls each time it rains it's important to take action. Water leaks from windows can not only cause destruction of your home's structure but also undermine your efforts to regulate the temperature in your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

This is a fairly simple fix that can be completed by any competent DIYer. Based on the severity of the problem the caulking used previously may require removal before a new layer of caulk can be applied. It is essential to keep in mind that when it comes to uPVC window repairs, do avoid the temptation to "over-caulk in order to make the area more difficult to clean and can reduce your energy efficiency.

Check that any drainage holes do not have debris in them, and also ensure that the sill pan has been angled correctly to drain away from the window. In more serious situations, you may have to replace the window.

Mold spots and rotten sills are also signs of water leakage. The fungus thrives in conditions of dampness and can spread quickly throughout the home.

It is also important to keep in mind that if the leakage originates from the glass in your double glazed windows, it is more likely to be a problem with the glass seal rather than the frame or sliding. A uPVC specialist can easily fix this issue by replacing the glass seal. This will restore the full insulation of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or loose and blow open with ease, it may be the hinges that are at fault. These are easily repaired by any DIYer who is skilled and can be done within a few minutes.

Almost every household in the UK will have either top hung or side-hung uPVC windows that use hinges and, just like any mechanical component they can wear down over time. It's easy to change the hinges on a window but it's much easier if someone else helps hold the frame.

It is also important to ensure that the uPVC hinges are being opened and closed in the correct direction. You can do this by looking for the arrow on each hinge. This shows which way the window should open.

The problem with the hinges on windows could be caused by improperly opening the window a certain way or by poor installation at the factory. Sending us a photo via our website will often resolve the problem. We are happy to offer suggestions.

It is also essential to ensure that the hinges are lubricated on a regular basis. This can be done by applying a light engineering oil on the hinges, we recommend using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It can also lower the chance of windows getting stuck and stop corrosion. Ideally, you should perform this every year. WD40 and other solvent based fluids are not recommended since they could damage parts of your uPVC window.

5. Draughts

Draughts in Upvc windows can be caused by a variety of various factors. First, the hinges because of wear and tear, may become displaced, which can cause a gap to form where the sash joins the frame. These can be easily fixed by giving them a thorough clean, however in the event that they are beyond repair it might be necessary to have them realigned or replaced. In addition, the interlock could be disaligned. It is located on the hinge side and might require to be cleaned. In some cases it might be necessary to replace these.

The seals may wear out or get damaged over time, allowing air to escape. Installing high-quality weatherstripping is a good way to stop draughts. Replace the windows made of upvc with low-emissivity glass. This will help to regulate indoor temperatures and lessen the possibility of draughts.

Another, and most effective ways to cut down on the draughts in your home is to use a draught excluder, these are usually fabric tubes which are filled with a kind of filler. They can be positioned on the windowsill on top. They will keep your home warm by blocking cold air.

With a bit of regular maintenance and repair windows made of upvc will provide excellent insulation and security for your home. However, it is important to realize that all windows have a life span and eventually, they will reach the point when it's more efficient to replace them than repair them. If you are experiencing issues with your upvc window it is recommended to speak with a professional as soon as you can.