How to Replace the Replacement Key Battery For the saab key programming 9-3

Saab owners must follow a set of special steps to install a second ignition key. It requires dealer service with the handheld computer known as Tech-2. Then the transponder must be replaced and a key need to be purchased.

Make sure to rotate your keys in order to prevent one from wearing out faster than the other. This will also ensure that your keys remain in top condition.

Replacement Case

Unlike the classic Saab keys of old, the new key fobs are equipped with electronics that make it difficult to duplicate. This has made theft of cars a lot more complicated than it was 20 years ago. However, it has made the replacement of lost keys a comparatively expensive task.

Saab 9-3 owners must have two keys that work. If one is lost, it costs a fortune to replace it in the vehicle because it requires replacing the CIM module and re-programming the locking cylinders. Dealers usually charge between $100 and $200 for this.

There are several ways to get around the high price. Some parts providers will use the code of a spare key to cut a new metal blade for less than the cost of the dealer. The key must be the exact same as the original for it to function in your vehicle.

Follow these steps to replace the case. You'll need an open-faced screwdriver and a lot of patience. Using the screwdriver, slowly pry the plastic apart and remove the emergency key from the case. After the case is open remove all electronics and put them back in the new case. Be sure to put the correct badge and key back inside the case, too.

Replacement Battery

The replacement battery for the Saab 9-3 is a low-cost component that can be replaced easily and quickly. The YouTube video of Cyclone Cyd demonstrates how you can replace the remote fob battery in only four steps. This tutorial is suitable for any modern saab key fob although the process might differ slightly.

The button is typically located just below the Saab logo on the back of the fob. The button is usually found on the back of the fob, close to the Saab Logo. Next use an screwdriver with a flat head to insert into the small hole of this button. This should be enough to open the fob's case to allow you to replace the battery.

Once you have installed the batteries CR1632, it is possible to put back together the remote key fob. You can then program it into your car. The procedure should take no more than an hour at most. It is a simple process that does not require any special equipment.

If you lose your key, the process is more complicated but it is still able to be completed. The dealer will need to verify the VIN of the car, and then request a replacement key blade and Saab 93 key programming TWICE module, both with the proper unique code. The dealer will then have to program the key using MDI, a brand new software tool.

Replacement Key Fob

The key fob is the part that locks and unlocks your car. It is equipped with a battery within. Batteries have a limited lifespan and will eventually fail. It's a common issue that affects all cars. The good thing is that you can change the batteries in most key fobs, and not have to replace the entire case. You can buy replacement fobs on Amazon that include all the electronics already in place, so you'll just pop open the case and replace the old batteries. You will need to remove the emergency key before you replace the batteries. To do this, place a small screwdriver that is flat into the slot that is in the middle. The case will split as you turn the screwdriver around it.

If you are about to replace the keys, make sure you have a spare because this can cut down your total cost by a substantial amount. If you do have a spare, you can request that the dealer cut a new key and program it to your car, which is cheaper than replacing the entire key fob.

If you don't have a spare, it is possible to add an additional key to your car, however this will require a lot of research and effort. The cost for adding a second key is around a hundred dollars and it also requires the programming of the car's computer. This can be done by a professional, but it's a costly option for the majority of owners.

Replacement Ignition

Contrary to earlier saab 93 key programming; www.Easyfie.com, vehicles, the latest SAAB 9-3 models use a much more sophisticated alarm system that is built around a coded key. This means that in the event that you lose your only working key, replacing it with an additional one could be extremely expensive as the car has to have a specific computer module added and it must also be programmed to accept a new key. Most locksmiths cannot do this, and even dealers will charge hundreds of dollars just to program the new key!

Dealers will charge you a premium to replace your car computer (also known as the CIM or saab 9-5 key replacement twice) If you lose the only working key. We can reprogramme the existing EEPROM inside your car's computer to make it ready for an additional key. This will save you more than 50% of the cost you pay at the dealer.

If you've been a faithful owner of a 03-11 SAAB 9-3, you likely know that the ignition key isn't the most robust. If your ignition key isn't working correctly, you should think about replacing it. They can become sticky and the buttons are known to fall off. Luckily, replacing the ignition key isn't as complicated as it seems, and it can be done quickly using the proper tools.