Repairs to uPVC Windows

uPVC is a fantastic option for modern homes. They are durable, long-lasting and easy to maintain. They don't rot or rust like aluminum and timber.

It is important to clean and oil UPVC doors and windows on a regular basis. This will help avoid unnecessary repair costs and improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows could cause severe damage to your home and may even be fatal. It is essential to make sure that your windows are in good working order.

For single pane windows it is relatively easy to replace them, and the replacement is usually able to fit into the frame of the previous one easily. If you have double glazing near me-paned windows which are held together by internal beading, it will be more difficult to remove and replace the panes that were previously in use. In this situation, it is necessary to buy plastic spacers to aid in fitting the new pane into the window frame.

If you are going to attempt to remove the window panes by yourself it is important to wear the appropriate safety equipment, including thick gloves and eye protection. It is also an excellent idea to lay down a drop cloth prior to when you begin working on the glass so that any shards will fall on the fabric instead of landing on the floor where they can be trampled on and cause further damage.

Once the glass is removed and the glass is removed, it's a good idea to seal the gap with clear packaging tape or duct tape to prevent drafts and water from entering the home until a professional can come out and fix the window. This will also act as a barrier that will prevent any intruders from gaining entry into your home. If the gap is particularly large, you may be interested in the security door with an integrated window, as this will offer the best of both worlds.

2. Sagging

uPVC is durable energy-efficient, cost-effective and economical alternative to timber sash window. However, over time, they can suffer from a variety of problems including sagging. A window that is sagging can cause problems with light, draughts or even security. It's crucial to act as soon as you notice your uPVC windows are sliding.

To fix a window that is sagging you can try repositioning the hinges. First, you'll need to open the windows to access the frame. Then, you can remove the top and bottom hinges with a screwdriver and adjust them clockwise or counter-clockwise. Once you've repositioned the hinges, close your window and test it for fitting. If you are happy with the size of the window, tighten the screws to secure them in the right position.

If you are unable to move the hinges, you might have to replace the seal. Over time, rubber seals lose their elasticity and dry out and cause them to lose tightness. It is crucial to replace your seal as soon as you can to keep your uPVC window watertight and draughtproof.

uPVC handles may also loosen. The majority of the time, this is caused by screws that have become loose over time. However, it can also happen because the handle mechanism has been worn out. Fortunately, it's easy to fix the loose uPVC window handle yourself. You'll first need to close the window and window repair do an experiment fitting. The corners of the sash need to align with the casing joint. If it isn't then you can use the screwdriver to loosen the handle. Then, you can turn the mechanism back into place.

3. Water Leaks

If you awake to wet floors and damp walls every time it rains it's important to take action. Windows that leak water do not only lead to the destruction of your home's structure but also hamper your efforts to control the temperature inside your home. The most common cause for leaking uPVC windows is that the sealant around the frame has been damaged or not present.

This is a relatively easy fix that can be completed by any competent DIYer. Depending on the severity of the problem the caulking used previously may require removal before a new layer can be applied. When it is time to uPVC repair, you should be careful not to over-caulk. This will only make your window more difficult to clean and reduce its energy efficiency.

Make sure that the drainage holes have no debris inside them and ensure that the sill pan has been properly angled to drain away from the Window repair. In more severe situations, you may have to replace the window.

Other indicators of long-term water leakage are rotted sills and the appearance of black spots of mold on the walls near the window. The is a fungus that thrives in damp conditions and can quickly spread across the home.

If the leakage occurs between the double-glazed glass it is more likely that the problem is with the seal rather than the frame. This can be easily corrected by an uPVC window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or loose and open with a breeze it could be the hinges that are at the fault. Any competent DIYer can replace these in a matter of minutes.

Nearly every home in the UK will have top-hung or side hung uPVC windows that have hinges and like any mechanical part they will wear out over time. It's easy to replace a hinge on a window, but it's easier if someone helps you hold the frame.

It is also worth checking that the uPVC hinges are opening and closed in the right direction. This can be done by looking for the arrow on each hinge, this indicates which way the window should open.

The issue could be caused either by opening the window incorrectly or by a poor installation in the factory. Sending us a picture via our website will often resolve the problem. We are more than happy to provide assistance.

Regularly lubricating hinges is also essential. Applying a light engineering lubricant to the hinges is an ideal way to do this. We recommend using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication will make the window easier to open and close. It also helps prevent corrosion and decrease the chance of sticking. This must be done at a minimum every year. WD40 or other solvent-based lubricants should not be used as they can cause damage to your uPVC windows.

5. Draughts

Draughts can be caused by several different causes. The hinges can also become disaligned as a result of wear, causing a gap where the sash and frame meet. If they're beyond repair, it might be necessary to get them re-aligned. Second, the interlock can also become misaligned. It is located on the hinge's side, and may need to be cleaned. In certain instances, it may be necessary to replace the hinges.

The second most frequent cause of draughts is the window seals. They are susceptible to being worn out or damaged over time, and will allow air to escape through these gaps. Replacement of these with high-quality weatherstripping is a good way to prevent draughts. Replace the windows made of upvc with low-emissivity glass. This will help to regulate indoor temperatures and lessen the possibility of draughts.

Another method of reducing draughts effectively is by using a Draught-exclusion device. These are usually made of fabric tubes filled with a filler, which can be put on top of your window sill. They will keep your home warm by blocking cold air.

The windows made of upvc can continue to provide excellent insulation and security in your home with regular maintenance and repairs. It is crucial to recognise that all windows have a life span and they may reach a point where it is more cost-effective to replace them rather than repair them. If you are having issues with your upvc windows, it is best to seek professional assistance immediately.