Repairs to uPVC Windows

upvc window repairs is a great option for modern homes. They are durable, long-lasting and easy to maintain. In contrast to aluminium and timber, they do not rust or rot.

Cleaning and lubricating regularly UPVC windows and doors is vital. This will reduce repair costs as well as increase energy efficiency.

1. Broken Glass

The broken glass in your windows could cause severe damage to your home, and could even be fatal. It is essential to take the time to ensure that you're doing everything you can to ensure that your windows are in good shape.

For single pane windows it is relatively easy to replace them, and the new window will usually fit inside the old frame very easily. However when windows with double panes are held in place by internal beading, it'll be more difficult to remove the panes that are in place and replace them with new ones. In this instance, it is necessary to buy plastic spacers to help the new pane fit into the window frame.

Wearing eye protection and thick gloves is essential when you are planning to remove the glass yourself. You should also lay down a dropcloth prior to you begin working on the window panes so that any shards of glass fall onto the fabric and not on the floor, where they could be trampled.

It's a great idea seal the gap after the glass has been removed. This will stop water and drafts from entering your property until a professional comes out to repair the window. This will also provide an obstruction to prevent intruders from getting into your home. If the gap is large, you might be interested in the security door with an integrated window, since it will provide the best of both worlds.

2. Sagging

Upvc windows and doors are a cost-effective energy efficient, durable and long-lasting alternative to timber sash windows. In time, they could develop a variety of issues that include sliding. A sagging window in uPVC can cause problems with light, draughts, and even security. It's important to take action immediately if you realize that your uPVC windows are falling down.

To repair a window that is sagging, you can try to reposition the hinges. To do this, you'll need open the window to access the frame. You can then unscrew both the top and bottom hinges with a screwdriver and adjust the hinges clockwise or counter-clockwise. Once you've repositioned the hinges, Upvc Window Repair close your window and check for an appropriate fit. If you're satisfied with the fit of the window, UPVC window repair you can tighten screws to hold them in place.

If you are unable to reposition the hinges, you might have to replace the seal. Over time, rubber seals lose their elasticity and become dry and cause their tightness to decrease. It is crucial to replace your seal as soon as you can in order to ensure that your uPVC window waterproof and draughtproof.

Upvc window repair handles can also become loose. This is typically caused by screws that have loosened over time, but it could be due to the handle mechanism getting worn out. Luckily, it's not difficult to fix a loose uPVC window handle yourself. First, you'll need to close the window and do a test fitting. The joints at the corners of the sash should align with the joint on the casing. If it isn't, you can use a screwdriver to loosen the handle and reverse the mechanism back into position.

3. Water Leaks

If you awake to damp floors and mouldy walls every time it rains it's important to take action. Water leaks from windows not only lead to the destruction of your home's structure but also hinder your efforts to control the temperature within your home. Most often, uPVC window leaks are caused by damaged or missing sealant.

This is a simple fix that can be done by any DIYer who has the ability. Based on the severity of the problem the caulking used previously might need to be removed before a new layer can be applied. When it comes to uPVC repair, you must be careful not to over-caulk. This will make your window harder to clean and decrease its energy efficiency.

It is important to check that any drainage holes are clear of debris and that the sill pan is angled in a way that allows it to drain away from the window. In more serious situations, you may need to think about replacing the window.

Other indicators of long-term water leakage include rotted sills and the appearance of black spots of mold on the wall near the window. This fungus thrives under humid conditions and can propagate quickly throughout the house.

If the leakage occurs between the double-glazed glass, it is more likely the issue is with the seal than the frame. This can be easily corrected by a uPVC window specialist who will replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

Hinges may be to blame if your uPVC window is difficult to open, or if it opens with a breeze. They can be replaced by any competent DIYer and can be done within a few minutes.

Like all mechanical parts hinges will wear out over time. It is very easy to change a window hinge, but it's easier if someone else helps hold the frame.

It is also important to ensure that the uPVC hinges are opening and closed in the correct direction. You can do this by looking for the arrows on each hinge. This shows which way the window should be opened.

The problem can be caused either due to opening the window in the wrong way or due to a poor installation in the factory. This issue can be fixed by sending us a photo through our website and we will be happy to give you advice.

It is also important to ensure that the hinges are lubricated on a regular basis. Applying an engineering lubricant that is light to the hinges is a great method of doing this. We recommend using an oil that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regularly lubrication makes the window easier to open and close. It can also stop corrosion and decrease the chance of sticking. The ideal time to do this at least once a year. WD40 and other solvent-based lubricants should not be used since they can damage your uPVC windows.

5. Draughts

Draughts in upvc windows can be caused by various factors. The hinges, also due to wear and tear can become misaligned, this causes an opening to appear where the sash meets the frame. This can be easily repaired by giving them thorough clean, however if they are beyond repair it may be necessary to get them realigned or replaced. The interlock may be unbalanced. It is located on the hinge side and might require to be cleaned. In some cases, it may be necessary to replace the hinges.

The next most common reason for draughts is window seals. These are prone to wear or damaged over time, and let air escape through the gaps. This can be avoided by replacing them with high-quality weatherstripping. Another option is to replace the window with low-emissivity glass, which will help regulate indoor temperatures and will lessen the risk of draughts.

Another method of reducing the amount of draughts is to use a Draught-exclusion device. These are typically fabric tubes filled with a filler, which can be placed over your window sill. These will help to block out cold air and keep your home warm and cozy!

The windows made of upvc can keep providing excellent insulation and security for your home by performing regular maintenance and repairs. However, it is important to recognise that all windows have a life span and there may come the point when it's more efficient to replace them than fix them. If you are experiencing problems with your upvc windows, it's best to seek professional assistance immediately.